Free usb devices software for mac

VST USB Hard Drive is a package that contains the driver for the USB Thin Drives.

This driver provides support for ATA and ATAPI storage devices using the ISD725, ISD200 or ISD300 USB Bridge chips.

Have you ever plugged in a USB device only to be underwhelmed by the reaction of OS X? It can be very confusing when the system seems to pay no attention to whats just been plugged in - did it even notice?
USB Monitor eliminates the guess work. It pops up a little window and provides the name of the device thats just been plugged in (or unplugged).
The window follows the visual style of the transparent windows for volume and eject.
Enhancements:
- Fixed memory leak.

This is the latest release for the QuickCam Pro cameras that allow you to use them on your USB based Power Macintosh.

Apple USB DDK is a development software package that gives you some of the tools that you need to write your own USB drivers.

Although USB to Ethernet adaptors are cheap and plentiful, Mac OS X drivers are not.
USB-to-Ethernet offers you USB to Ethernet Adaptor Drivers.
There are two basic catagories of USB-To-Ethernet adaptors:
- USB 1.1 devices that use a Pegasus driver.
- USB 2.0 devices that use a AX8817x driver (or its successor, the AX88772).
Each disk image includes an installer for Panther or Tiger, and a "src" folder containing the corresponding xCode projects.
Installation
Download and mount the appropriate driver disk image listed above, run the corresponding installer for Panther or Tiger, and then restart your system as suggested. The Installer will ask you to authenticate so it can place the corresponding driver in "/System/Library/Extensions/" with the correct file permisions to load as a kernel extension.
Next, plug-in your Ethernet adaptor with a live Ethernet cable attached. When you open the Network Preferences panel, it should inform you that a new port has appeared and ask if you want to enable it. Enable the new port and apply your network settings. Thats it.
Each driver is pre-configured to recognize a handfull of common devices. If your device does not appear to be recognized by the driver, you might have to add it to the Info.plist file, which is located inside the USBPegasusEthernet.kext or USBAx8817x.kext directory. You can use the System Profiler or USBProber tool to find the corresponding Product ID and Vendor ID.
To uninstall the driver, make sure any USB adaptors are disconnected, and then drag the corresponding driver in /System/Library/Extensions/ USBPegaususEthernet.kext or USBAx8817x.kext to the trash. You may need to authenticate that you have administrator privileges.
USB 1.1 Performance
The Pegasus chipset provides a USB 1.1 compatible implementation which could be a concern for some users. USB 1.1 runs at 1.5 Mbps (low speed) or 12 Mbps (full speed). For best performance, its important to isolate any low speed devices on a separate bus. Mice and keyboards often run at low speed.
Using the Link Rate tool in IPNetMonitorX, I measured the link rate to another device on my LAN as 6 Mbps. The built-in Ethernet on my 12" PBG4 reported 44 Mpbs. When I measured the link rate to the next hop router through my cable modem, it reported 1 mbps. It didnt make any difference whether I used Ethernet built-in or the USB-To-Ethernet adaptor. Finally, I downloaded a 2.2 MB file to compare the throughput using the Monitor tool.
Both downloads took 5 seconds, but Ethernet built-in reached a peak rate of 589 KBps versus 579 kBps. Repeating the experiment several times produced similar results. Ethernet built-in might be 1-2% faster, but performance was clearly limited by the speed of my cable modem (Your Mileage May Vary).
USB 2.0 Performance
The AX8817x chip set provides a USB 2.0 compatible implementation which runs at up to 480 Mbps (high speed), so it should be possible to keep up with 100 Mbps fast ethernet as long as there are no other slower devices on the same bus. To test this I copied a 64.8 MB music file to my PBG4 laptop connected through a LinkSys USB200M Ethernet Adaptor (en3) and compared this to the same file transfer using Built-in Ethernet (en0).
Both transfers reached 10 MBps (80-90 Mbps) and took about 10 seconds. I repeated the test in the other direction.
While the USB-To-Ethernet adaptor was slightly slower, at 80 Mbps there was little noticeable difference. Files moved quickly from one system to another via 100 Mbps fast Ethernet. Copying the same file using AirPort wireless took 50-90 seconds.
Stability
While other USB-To-Ethernet drivers are reported to be buggy, I havent encountered any stability problems to date. The adaptor turns off when the computer goes to sleep and comes back on when the computer awakes. It does not support "Wake On LAN" at this time.
Wrap Up
This USB-To-Ethernet Adaptor combination could be an attractive solution for a Mac Mini, or old iBook used as an Internet gateway or server. Im particularly fond of using old laptops as servers since they are compact, quiet, use little energy, and include their own battery backup.

Requirements:
PCI based PowerPC, Mac OS X 10.2.3 or later.

QPS Que! USB CD-RW is a driver package that adds support for your QPS Que! USB CD-RW Drive (4X2X8 or 4X4X8) on Mac OS X.

This driver provides support for ATA and ATAPI storage devices using the ISD725, ISD200 or ISD300 USB Bridge chips as well as the Cypress SL11RIDE, SL11-Combo, FX and FX2 USB Bridge chips.

Completly freeware.